60A MPPT Solar Charge Controller 12V/24V/36V/48V Regulator Auto USA Authorized

Description: 60A MPPT Solar Charge Controller 12V/24V/36V/48V Regulator Auto USA Authorized60A MPPT Solar Panel Regulator Charge Controller DC12/24/36/48V Auto Max PV 190V FEATURE:❶【Software Update Version】100% MPPT 60A solar charge controller Intelligent, Max efficiency ≥98.1%, PV utilization ≥99%.Built-in DSP controller with high performance Automatic battery voltage detection 12V/24V/36V/48V, Make sure batteries' voltage more than 12V to boost controller and make sure battery has enough power to Self-detection when connected to the controller. ❷Fit for USER(can be set Lithium, Lifepo4, Li(NiCoMn)O2)/Vented/Flooded/Sealed/Gel/NiCd battery.User programmable for absorption voltage/Floating voltage/Low voltage disconnect./Load Timer. Real-time energy recording. ❸Blacklight LCD Dispaly PV voltage/output power/Battery voltage/charging current/working mode/Temperature, ☀ TROUBLESHOOTING function and LCD display and can help users not only check the whole system operating data and statuses but also quickly identify system faults and modify parameters. ❹Intelligence Fan-on temperature >45℃ and off < 40℃,Porous heat dissipation.and fan use BEARING technologies increase life UP TO 5000hrs in normal use. ❺【What You Get】we consider that the larger diameter of the wire will be greater cost for customers, so we designed two connectors for each pos and negs on solar and batteries connectors. copper wires:9AWG.Hope you love it. Charging 3-stage: constant current(MPPT), constant voltage(Absorption Voltage), floating chargeSelectable battery type Vented / Sealed / Gel / NiCd / Lithium battery (default is Sealed) (defined voltage for other battery by user)Soft start time ≤1S, Dynamic response and recovery time 100usMax efficiency ≥98.1%, PV utilization ≥99%In order to reduce the cost of electricity caused by high current, PV and battery each have two terminalsMULTIPLE ELECTRONIC PROTECTIONSShort-circutingReverse-currentOverchargingOverloadOver-dischargingReverse polarity protection Notes: The output terminal is for lamp only( 12V system less 60W, 24V/36V/48V system less 100W ),and it will be burnt if connecting to other loads. The output for battery is no polarity reverse protection. Remarks: 1. The maximum PV input voltage (Voc): DC160V (The controller can not work with this long duration voltage, which will interrupt the controller. Refer to the input voltage of PV). 2. The output port is only for lamps (12V system less 60W, 24V/36V/48V system less 100W) and will be burned if connected to other loads. The battery output is not reverse polarity protection. 3. Always connect the battery first!!! Make sure the battery voltage is sufficient for the controller to recognize the correct system voltage. The order of dismantling contradicts the order of wiring. 4. Do not connect any inverter/wind/generator or charger to the controller, please connect the inverter to the battery side. 5. Ensures the solar input voltage exceeds 3V or more than the battery voltage and the total input power exceeds the max. , the charging current is almost zero when the controller has trickle charge. You can Put two pieces 60A in parallel ,So total is MPPT 120A. ParameterModel NameMPPT-60ACharging modeMPPT Maximum power point tracking automaticallyCharging3-stage:constant current(MPPT), constant voltage(Absorption Voltage), floating chargeSystem typeDC12V/24V/36V/48V Recognition automaticallySystem voltage automatic recognition12V system (DC9V-DC15V)24V system (DC18V-DC29V)36V system (DC30V-DC39V)48V system (DC40V~DC60V)Soft start time≤1SDynamic response and recovery time≥98.1% (Voc is 1.5 or 2 times than battery, then it’s best efficiency)PV utilization≥99%Input specificationVoc from PV( Make sure the Voc of PVmeeting the requirement as right. Voc is 1.5 or 2 times than battery, then it’s best efficiency. )12V system (DC20V~DC80V)24V system (DC37V~DC105V)36V system (DC50V~DC160V)48V system (DC72V~DC160V)The maximum PV input voltage (Voc)DC190V(The controller can’t work at this voltage of long duration that will break controller. Please refer to Input voltage from PV.)The maximum PV input power(The total power rated of PV can’t be over this watt that will break the controller.)12V system (720W)24V system (1440W)36V system (2100W)48V system (2800W)Output specificationSelectable battery type(default is Sealed)Vented/ Sealed / Gel / NiCd / Lithium battery(defined voltage for other battery by user)Absorption Charging VoltageRefer to Batteries charging referenceFloating Charging VoltageRefer to Batteries charging referenceOvercharging protection voltage12V system (15V)24V system (30V)36V system (45V)48V system (60V)Rated output current60ATemperature Coefficient±0.02%/ centi-degreeAutomatic temperature compensation14.2V-(Max temperature-25 centi-degree)*0.3Output voltage ripple-peak100mVOutput voltage accurac≤±1%Input Anti-intrusion protectionyesTemperature Protection75°CTemperature increased protectionOutput power will reduce when it’s more 70 °COutput power will be normal when it’s less 55 °CFan-on temperature>40 °CFan-off temperature<35 °CAcoustic noise≤40dBCooling wayForced air coolingComponentsImported materials, Accord to EU standards, Industrial grade range.Environmental requirementsMeet 2002/95/EC; No cadmium, hydrides and fluoridesSecurity LevelAccord to CE, PSE, FCC, EMC, EN60950Electromagnetic CompatibilityAccord to EN61000, EN55022, EN55024EnclosureIP21Net weight(Kg)1.1Gross weight(Kg)1.2 COPPER COILSTrue MPPT controller, The Three copper coils play a step-down roles to make your system work more stable. TRANSFORMERThree Electronic transformer, more safeMULTIPLE ELECTRONIC PROTECTIONS: Short-circutingReverse-currentOverchargingOverloadOver-dischargingReverse polarity protectionFAN COOLING Good Heat dissipationIntelligence Fan-on temperature >45℃ and off < 40℃ , let your controller feel cooling.Fan use BEARING technologies increase life UP TO 5000hrs in normal use. TipsAlways connect the battery first!!! Make sure enough batteries’ voltage let the controller recognize the right system voltage. The disassembly sequence is contrary to the wiring order. NEVER connect the solar panel array to the controller without a batteryDO NOT connect any Inverter/ wind/ Alternator or Charger into the charge controller! connect the Inverter directly to the battery.Ensures solar input voltage is higher than 3V or more than batteries’ voltage and total input power in the range. if the input power is too low for max input power, it may appear to have been discontinued., the charging current almost is zero when the controller is floating charge.Parameter Setting Rules：Floating voltage > Low voltage reconnect > Low voltage discharge.The solar controller will stop output when the battery is under 10.7V. The LCD will be blank when the battery is under 8V and it will re-output when the battery up to 12.6V (adjustable).Install the Charger controller to the battery as close as possible. Tighten the wire, Carefully read battery manuals before operation.When the controller makes a buzzing sound because of It's working hard to dissipate heat for your controller. Rest your heart, it will be stop when the temperature return to normal.Remove all the debris around the controller ( leaving a space of approx. 5.91in ). Make sure all connections going into and from the controller are tight. Do NOT let the positive (+) and negative (-) terminals of the battery touch each other. Package includes1x 60A MPPT solar controller 1x user manual 1x Mounting caps 1x Screws About usDelivery detailsTerms of salesPaymentContact USAbout us PowMr is a global solar energy innovation application company. In the past ten years, we have provided related products and services to more than 150 countries around the world, and are committed to promoting solar energy products to more application fields and scenarios. We advocate new energy life, improve new energy ecological technology, protect the natural environment, and realize the common progress of man and nature. Why PowMr? - Fast Delivery - Free Shipping - 24 months warranty 一Avg. response time 1 Hrs(WorkingDay) - PowMr Everywhere 1. “Highly Quality first, customer orientation”is our purpose. 2. PowMr will be committed to provide the best service to you!Delivery details🚚 Our warehouse is located in US, your orders will be shipped from our US warehouse. 🚚 PowMr offers a variety of shipping methods such as USPS, UPS, FEDEX. Any items that qualify for free shipping will be identified on the product listing page. 🚚 Your order will be sent out WITHIN THE HANDLING TIME. HANDLING TIME are based on 2 business days (Monday to Friday) excluding Holidays and weekends . Delivery times may vary, especially during peak periods. 🚚 The order of multi items may be sent via MULTI PACKAGES. If your order is including MULTI ITEMS, we may send the item to you via MULTI PACKAGES. If something is missing in the first package you received, please don't open a case or return, please contact us first, we will check if your order is sent via multi packages. 🚚 All items will be shipped to the address on Ebay order. Buyers have full responsibility to provide us with the correct delivery address on the checkout page before payment is made. 🚚 Please be aware that PO Box cannot receive items, please DO NOT fill in the PO Box address.Terms of sales🔶 For purchases made directly from our online store, if for any reason you are not fully satisfied with your purchase, you may return your products with the original package within 30 days as long as they are new, undamaged, and unmodified. 🔶 PowMr will pay the shipping costs of the returned item(s) for the following reasons: carrier damage, defective product, product inconsistent with advertisements, incorrect product received. For all other reasons, customers are responsible for the return shipping fees. 🔶 If damage results due to improper handling during the setup or installation, whether done professionally or by the customer, then the product is no longer eligible for replacement or refund. 🔶 Please note: We will not accept returns with product modifications as it voids our warranty policy. Any modified products received will be returned to you at your expense. 🔢 Please be prepared with your invoice or the following information： 1. Order number 2. Proof of purchase 3. Video or photo of the faulty product (if applicable) 4. Mailing addressPayment• We can accept the payment by Paypal，Payonner. • Buyers are required to carefully follow payment instructions on the checkout page, and note down any necessary details on it (e.g. bank account details). • If buyers fail to follow the instructions on the checkout page, We are not liable for any unidentified payments and subsequent delivery delays.Contact US📧 Please contact us via eBay message if you have any questions. We will reply to you within 24 hours (Monday to Friday) excluding Holidays and weekends.📧 If the device has any problem before you open the return/case, please feel free to contact us. We have a professional engineer and after-sales team, we will try our best to help you out. 📧 Feedback is important to us, we will leave positive to our customers. Please email us before leaving any 1 or 2 ratings, negative feedback or opening any dispute. 📧 We understand that you might have concerns, and we will do our endeavor to resolve the issues. Please give us the opportunity to resolve any problem.

Price: 76.99 USD

Location: Walnut, California

End Time: 2024-10-14T07:55:03.000Z

Shipping Cost: 0 USD